Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
In this article below you can locate a good deal of outstanding answers pertaining to Installing A Bathtub.
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and occasionally, tiling skills. Replacing an old bath tub with a new one is additionally a moderately difficult task. If the old tub is conveniently available, the task can relocate easily; if you need to open up a wall to remove the old tub and also place the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old tub and also embeded in the new one. Make certain you have actually certified yourself for the task and also are comfortable attempting it. Instead of working with a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This write-up will certainly aid you set up a new bathtub in your bathroom if you have actually currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also material list ought to comprise the following:
Planning for the Installation
First of all, the sustaining structure provided with the bathroom should be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be suited its last setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be fairly problematic as a result of the restricted accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing substance.
Before going on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required placement. The wood boards are useful in evenly spreading the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four small factors.
The next goal is to ensure that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and also adjusting the feet on the bath tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Switch on the water supply and inspect all joints as well as new pipework for leakages and tighten them if required. Fill up the tub and likewise examine the overflow electrical outlet and also the typical electrical outlet for leakages.
Ultimately, take care of the bath paneling as defined in the maker's user's manual. Tiling and securing around the tub should wait until the tub has actually been utilized at the very least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Protect the tap in position with the maker offered backnut. Once the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate sufficient to fracture a stiff seal, causing the water to penetrate the wall surface between the bathroom and the tiling, bring about complications with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, as well as are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water prior to securing, to allow for the motion experienced when the tub remains in use. The sealer can fracture fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the market. It is a good idea to fit the ceramic tiles using waterproof or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that editorial about Installing A Bathtub from someone on a different web page. Don't hesitate to set aside a second to share this write-up if you liked it. We treasure reading our article about Installing A Bathtub.
We're on standby! Report this page